# Roomba error 14: the robot cannot detect the bin

Roomba error 14 means the robot does not detect an installed bin. The quickest fix is to take the bin out, push it back in until it seats fully, and wipe the bin contacts on the bin and the robot.

Updated Oct 27, 2026. HTML version: https://robotsforthat.com/guides/roomba-error-14/

## Short answer

Error 14 means your Roomba cannot detect its bin. The usual causes are a bin that is not fully seated after emptying and dirty metal contacts on the bin or inside the robot. iRobot says to confirm the bin is installed properly and to clean the contacts on both parts with a clean, lightly damp melamine foam pad such as a Magic Eraser. If the error stays after that, iRobot says you may need a replacement bin.

| What you see | Likely cause | Fix |
|---|---|---|
| Error 14 right after emptying the bin | The bin is not fully seated in the robot | Take the bin out, push it back in until it sits flush, then press CLEAN to restart |
| Error 14 with the bin pushed all the way in | Dust or grime on the bin contacts or the matching contacts in the robot | Wipe the contacts on the bin and on the robot with a clean, lightly damp melamine foam pad, let them dry, refit the bin |
| Error 14 plus the troubleshooting and full bin lights | Same bin detection fault shown on the 700 and 800 series lights (the 600 series has no full bin light) | Reseat the bin and clean the contacts as above |
| WiFi 600 or 800 says open the iRobot HOME app | Same bin detection fault on a connected model | Open the app for the guided steps, then reseat the bin and clean the contacts |
| Error 14 stays with a clean, seated bin | A stuck error in the robot software | Reboot the robot using iRobot's reboot steps for your series, then test again |
| Error 14 on every run, contacts clean | Bin fault, such as a failed contact strip | Order a replacement bin from the iRobot Store or contact iRobot Customer Care |
| Contacts look bent or corroded | Damaged contact pins on the bin or robot | Owner fix: an iFixit answer suggests checking the pins for bends or corrosion and trying a known good bin to tell a bad bin from a bad robot |

## Fix Roomba error 14 step by step

Error 14 is one of the easier Roomba codes to clear. The robot reads the bin through a set of small metal contacts. If the bin sits a little high, or the contacts are dirty, the robot thinks the bin is missing and stops. Work through these checks in order and test after each one. All fixes below come from iRobot's support pages unless they are marked as owner reports.

- Turn the robot off and lift the bin out.

- Empty the bin and check that nothing is caught where the bin meets the robot.

- Find the metal contacts on the bin and the matching contacts in the bin slot on the robot.

- Wipe both sets with a clean, lightly damp melamine foam pad, such as a Magic Eraser. Let them dry.

- Push the bin back in until it is fully seated and flush with the body.

- Press CLEAN. If the error is gone, you are done.

- If it comes back, reboot the robot and test again.

## Which Roombas show error 14 and what they say

iRobot lists error 14 for the 600, 700, 800 and 900 series. On the 600, 700 and 800 series the robot says error one four, then asks you to reinstall the bin and press CLEAN. WiFi connected 600 and 800 models say error one four and tell you to open the iRobot HOME app for help. The 900 series says error fourteen and asks you to reinstall the bin and press CLEAN.

On the 700 and 800 series the troubleshooting light and the full bin light both turn on. The 600 series has no full bin light, so you only see the troubleshooting light and hear the message. Home automation tools that read the robot's status list code 14 as bin missing, which matches iRobot's meaning.

To reboot, iRobot says to hold CLEAN for 10 seconds on WiFi connected 800 and 900 models, and to hold HOME and SPOT for about 10 seconds on 500, 600 and 700 models without WiFi. Some 600 series robots with a green dot under the bin need the battery taken out for 30 seconds instead. A reboot does not erase maps or schedules.

## The part to replace if error 14 keeps coming back

If the bin is seated, the contacts are clean and a reboot does not help, iRobot says you may need a replacement bin. The bin is the part that carries the detection contacts, so it is the usual part to swap. On the 800 and 900 series this is the AeroForce bin. You can order one from the iRobot Store or an authorized retailer.

Owners on iFixit suggest one more test before buying. If you can borrow a bin that works in another robot of the same series, fit it. If the error clears, the old bin is the problem. If it stays, the contacts inside the robot are more likely at fault, and that is a job for iRobot support rather than a new bin.

## When to contact iRobot support or claim warranty

Contact iRobot Customer Care if error 14 stays with a known good bin, if the contacts in the robot look damaged, or if your robot is still under warranty. A covered robot may get a new bin at no cost, so check your purchase date before you order a part.

iRobot asks you to have the robot charged and with you, its serial number, and proof of purchase from an authorized retailer for a warranty claim. Error 14 on its own rarely means the whole robot needs replacing. A new bin costs far less than a new Roomba.

## Questions people ask

### What does error 14 mean on a Roomba?

The robot does not detect an installed bin. Reseat the bin firmly and clean the metal contacts on the bin and the robot with a lightly damp melamine foam pad.

### Why does my Roomba say error 14 when the bin is in?

The bin is usually not fully seated, or the contacts are dirty. Take it out, wipe the contacts on both parts, let them dry and push the bin back until it sits flush.

### How do I reset error 14 on a Roomba?

Fix the bin first, then press CLEAN. If the code stays, reboot the robot. On WiFi 800 and 900 models hold CLEAN for 10 seconds; on 600 and 700 models without WiFi hold HOME and SPOT for about 10 seconds.

### Do I need a new bin for Roomba error 14?

Only if the error stays after you reseat the bin, clean the contacts and reboot. iRobot says a replacement bin may then be needed. Try a known good bin first if you can.

### Does error 14 damage the Roomba?

No. The robot stops to protect itself because it cannot confirm a bin is fitted. Nothing on iRobot's error 14 page says the fault harms the robot.

## Sources

1. [iRobot: Roomba Error 14 (600, 700, 800 and 900 series)](https://support.irobot.co.uk/articles/en_GB/Knowledge/8966)
2. [iRobot: Roomba 800 series error messages chart](https://support.irobot.ca/articles/en_US/Knowledge/7265)
3. [iRobot: Roomba 600 series error messages chart](https://homesupport.irobot.com/articles/en_US/Knowledge/641)
4. [iRobot: Rebooting your robot, all Roomba and Braava models](https://support.irobot.ca/articles/en_US/Knowledge/9087)
5. [iRobot: Cleaning the Roomba 800 and 900 series AeroForce bin](https://homesupport.irobot.com/articles/en_US/Knowledge/8994)
6. [openHAB iRobot binding: robot status error code list](https://next.openhab.org/addons/bindings/irobot/)
7. [iFixit Answers: What does error 14 mean (owner answer)](https://www.ifixit.com/Answers/View/975717/What+does+error+14+mean)