Flashforge Adventurer 5M Pro vs Flsun T1 Pro
Researched by Riley Hart · prices checked Nov 4, 2026
As of Nov 4, 2026, the Flashforge Adventurer 5M Pro costs $569 and the Flsun T1 Pro costs $549, so the Flsun T1 Pro is $20 cheaper. The Flashforge Adventurer 5M Pro scores higher in our ranking (7.9 vs 7.8 out of 10). Pick the Flashforge Adventurer 5M Pro for enclosed printing in small spaces. Pick the Flsun T1 Pro for makers who want very fast PLA and PETG prints. The Flsun T1 Pro wins 4 of 4 points we can measure.
Who wins, point by point
The Flsun T1 Pro wins 4 of 4 points we can measure. Built from today's prices, the specs and independent tests for these two robots.
| Adventurer 5M Pro | T1 Pro | Winner | |
|---|---|---|---|
| Price today | $569 | $549 | T1 Pro |
| Top print speed | 600 mm/s | 1000 mm/s | T1 Pro |
| Max nozzle temp | 280°C | 300°C | T1 Pro |
| Release year | 2023 | 2024 | T1 Pro |
- Best for enclosed printing in small spaces
- You want to spend less (saves $20)
- You care most about top print speed (1000 mm/s vs 600 mm/s)
- You care most about max nozzle temp (300°C vs 280°C)
- Best for makers who want very fast PLA and PETG prints
- Build volume
- 220 x 220 x 220 mm
- Max speed
- Up to 600 mm/s travel
- Multicolor
- No
- Enclosure
- Yes
Compact enclosed CoreXY printer with filters and quick nozzles
Full Flashforge Adventurer 5M Pro review, pros and cons →- Build volume
- 260 mm diameter x 330
- Max speed
- Up to 1,000 mm/s
- Multicolor
- No
- Enclosure
- Yes
Very fast delta printer with a tall round build area
Full Flsun T1 Pro review, pros and cons →Side by side
| Flashforge Adventurer 5M Pro | Flsun T1 Pro | |
|---|---|---|
| Price | $569 | $549 |
| 3 year cost | $569 | $549 |
| Our score | 7.9/10 | 7.8/10 |
| Rank in 3D printers | #12 | #13 |
| Status | on sale | on sale |
| Warranty | 1 year limited on the printer, 3 months on extruder parts (Flashforge) | Not checked |
| Build volume | 220 x 220 x 220 mm (Flashforge) | 260 mm diameter x 330 mm tall (Flsun); The Gadgeteer and 3DPrint.com say about 285 mm of height is usable |
| Print speed | Up to 600 mm/s travel, 20,000 mm/s2 acceleration (Flashforge); 3DPrint.com says 200 to 300 mm/s in practice | Up to 1,000 mm/s, 30,000 mm/s2 acceleration (Flsun); 3DPrint.com printed at up to 600 mm/s in ASA and high speed PLA |
| Multi color | No, single filament | No, single filament (TechRadar) |
| Enclosure | Yes, enclosed shell with foam gaskets and dual filtration (Flashforge, 3DPrint.com) | Yes, acrylic sides and smoked glass front (The Gadgeteer); no dedicated chamber heater (3DPrint.com) |
| Auto leveling | Yes, full auto calibration; about 10 minutes (3DPrint.com) to 15 minutes (3Dnatives) | Yes, fully automatic leveling with no manual Z offset (The Gadgeteer) |
| Max nozzle temp | 280 C (Flashforge) | 300 C, 0.4 mm brass nozzle (Flsun, The Gadgeteer) |
| Heated bed | Yes, Flashforge says up to 100 C; 3Dnatives lists 110 C | Yes, up to 110 C with textured PEI plate (Flsun) |
| Filament types | PLA, PETG, ABS, ASA; TPU, PLA CF and PETG CF with 0.6 or 0.8 mm nozzles (Flashforge) | PLA, PETG, TPU, ABS, ASA, PA, PC, PET (Flsun, The Gadgeteer); ABS warped and failed for 3DPrint.com |
| Connectivity | Wi-Fi, Ethernet, USB (Flashforge) | Wi-Fi, Klipper web interface, USB drive, OTA updates (The Gadgeteer, 3DPrint.com) |
| Camera | Yes, built in camera for monitoring (Flashforge) | Yes, for timelapse and remote monitoring (The Gadgeteer); 3DPrint.com saw timelapse cutouts on long prints |
| Noise | Flashforge claims 50 dB in low noise mode and 55 dB standard; 3DPrint.com measured 68 dB average, 79 dB max, 46 dB min | Flsun claims as low as 55 dB; 3DPrint.com measured 71 dB average with 91 dB peaks |
| Assembly | About 95% pre assembled; remove transport screws, attach PTFE tube and spool holder (Flashforge, 3Dnatives) | Partial assembly, about 1 hour (3DPrint.com) to a few hours (The Gadgeteer) |
| Weight | 380 x 400 x 453 mm without spool holder (Flashforge); weight not listed | 18.41 kg net; 436 x 490 x 835 mm (The Gadgeteer) |
| Best for | enclosed printing in small spaces | makers who want very fast PLA and PETG prints |
| Skip if | you need large or multi color prints | you need a quiet printer or a square build plate |
Specs are maker claims unless a reviewer is named. Prices from the stores we link, checked daily.
What reviewers found
Flashforge Adventurer 5M Pro
- 3DPrint.com: A full volume ASA print took 24 h 44 min with no warping and a 100 mm cube measured 99.70 x 99.71 x 100.02 mm. Measured 68 dB average and 79 dB max. Ran with 100% uptime over a month; TPU needed 30 to 40 mm/s. Source
- 3Dnatives (9.5/10): Scored 9.5/10 with 10/10 for print quality. Auto calibration took about 15 minutes with no manual input. Cons were a confusing slicer transition, small build volume, no multi material and a rear mounted spool. Source
Flsun T1 Pro
- 3DPrint.com: Over 300 hours of printing with no part failures. Measured 71 dB average and 91 dB peaks versus Flsun's 50 dB claim. Parts came out slightly undersized, for example 98.85 mm on a 100 mm Y test, and ABS warped. Source
- The Gadgeteer: Called it the fastest printer the reviewer had used; a vase took about 40 minutes. Zero clogs and zero manual leveling across dozens of prints. Loose display ribbon and menus with no back button. Source
Questions buyers ask
Which is better, the Flashforge Adventurer 5M Pro or the Flsun T1 Pro?
The Flashforge Adventurer 5M Pro scores higher in our ranking (7.9 vs 7.8 out of 10). Pick the Flashforge Adventurer 5M Pro for enclosed printing in small spaces. Pick the Flsun T1 Pro for makers who want very fast PLA and PETG prints.
Which is cheaper?
The Flsun T1 Pro at $549, versus $569 for the Flashforge Adventurer 5M Pro, checked Nov 4, 2026.
What is the difference between the Adventurer 5M Pro and the T1 Pro?
Build volume: 220 x 220 x 220 mm (Flashforge) on the Adventurer 5M Pro, 260 mm diameter x 330 mm tall (Flsun); The Gadgeteer and 3DPrint.com say about 285 mm of… on the T1 Pro. Print speed: Up to 600 mm/s travel, 20,000 mm/s2 acceleration (Flashforge); 3DPrint.com says 200 to… on the Adventurer 5M Pro, Up to 1,000 mm/s, 30,000 mm/s2 acceleration (Flsun); 3DPrint.com printed at up to 600… on the T1 Pro. Multi color: No, single filament on the Adventurer 5M Pro, No, single filament (TechRadar) on the T1 Pro.
Also consider at this price
See all ranked →More comparisons
- Bambu Lab P1S vs Flashforge Adventurer 5M Pro
- Elegoo Centauri Carbon 2 vs Flashforge Adventurer 5M Pro
- Flashforge AD5X vs Flashforge Adventurer 5M Pro
- Bambu Lab P2S vs Flashforge Adventurer 5M Pro
- Creality K2 vs Flashforge Adventurer 5M Pro
- Creality K1C (2025) vs Flashforge Adventurer 5M Pro
- Bambu Lab A1 vs Flashforge Adventurer 5M Pro
- Elegoo Centauri 2 vs Flashforge Adventurer 5M Pro
All 3D printers, ranked
See the ranking →Affiliate links. We may earn a commission. It never changes our score. Disclosure
We check prices every morning and compare them with each model's 2026 low. One email when real deals land, plus our 5 minute Friday roundup. Unsubscribe anytime.