- Build volume
- 211.68 x 118.37 x 200 mm
- Max speed
- Up to 170 mm/h
- Multicolor
- No
- Enclosure
- Yes
Two quick taps and get the right robot for them, with today's price.
Creality HALOT-X1
Beginner friendly 16K resin printer with twist release plate
Researched by Riley Hart · updated Nov 3, 2026
Is the Creality HALOT-X1 worth it? The HALOT-X1 is one of the easiest resin printers to start with: it needs no leveling, and its twist release plate frees prints without scraping. It costs $469 as of Nov 4, 2026, and TechRadar scored it 4.5/5.
The HALOT-X1 is one of the easiest resin printers to start with: it needs no leveling, and its twist release plate frees prints without scraping. It suits beginners printing miniatures, jewelry or small models who want 16K detail at a mid range price. Skip it if you print in a cold room or want large parts, since it has no heated vat and a 10 inch plate.
Best for: beginners printing detailed miniatures. Skip if: you print in a cold room or need large parts.
Specs
- Build volume
- 211.68 x 118.37 x 200 mm (Creality)
- Print speed
- Up to 170 mm/h (Creality claim)
- Multi color
- No, resin printer prints one resin at a time
- Enclosure
- Yes, hinged UV blocking lid; DIY Machines found it needs 82 cm of height when fully open
- Auto leveling
- Arrives pre leveled with a build plate that needs no calibration (Creality); no leveling was needed for TechRadar, GamesRadar+ or DIY Machines
- Max nozzle temp
- Not applicable, resin (MSLA) printer with no nozzle
- Heated bed
- No heated vat on the printer; the optional AFU preheats resin to 30 to 35 C (Creality). GamesRadar+ listed the missing heated vat as a con
- Filament types
- Not applicable, uses 405 nm resin; slicing with HALOT BOX or Chitubox (Creality). DIY Machines found no Lychee profile
3 year cost of ownership
- Robot
- $469
- Total
- $469
No subscription. Running cost is mostly resin, release film and wash fluid, which depend on use. Creality sells HALOT-X1 spare vats and release films, but we did not confirm their prices, so no 3 year total is computed.
Status and safety
- US availability
- ● On sale
- Recalls
- ● No Creality robot recall in the CPSC database as of Nov 4, 2026. Checked daily.
- FCC authorized
- Not checked
- Company
- ● Active
- Warranty
- ● Not checked
Price history
Tracked dailyTracking started Nov 4, 2026 at $469.
Each day adds a point. Turn on a price alert to hear about drops.
Where to buy
- Amazon
- See price →
- Creality US store (HALOT-X1 Combo with 10 kg resin)
- $469 →
- Micro Center (HALOT-X1 Combo, in store only)
- See price →
Affiliate links. We may earn a commission. It never changes our score. Disclosure
Pros
- No leveling needed out of the box
- Twist release plate frees prints in seconds
- Sharp 16K screen with 14 x 19 micron pixels
- Optional AFU auto feed and resin preheat
- Quick 10 minute setup
Cons
- No heated vat or camera on the printer
- AFU auto feed was unreliable for TechRadar and needs manual top ups
- Slight first layer squash affects precision
- Slow Wi-Fi transfers and a basic interface
What independent reviewers found
- Reviewed as the PioCreat HALOT-X1. About 10 minutes from unboxing to printing, no leveling, and the quick release plate freed prints in about 3 seconds. Near 100% success over more than a month and several litres of resin. The AFU auto feed would not work properly.
- TechRadar · 4.5/5
- Tested over a few weeks with D&D miniatures, terrain and a large monster model. Print quality was hard to tell apart from the Elegoo Saturn 4 Ultra 16K. Called it probably the best introduction to resin printing the reviewer had seen. No heated vat or camera.
- GamesRadar+
- Measured about 49.1 dB at 1 m. 1 of 10 prints failed to stick. A 20 mm test cube came out 20.67 x 19.95 x 19.92 mm with slight first layer squash. The AFU did not fully empty the vat.
- DIY Machines
Spec history
Checked dailyNo spec changes since we started tracking on Nov 4, 2026.
Email me when HALOT-X1 gets cheaper
We check prices every morning. One email per real drop. Unsubscribe anytime.
Own one? Tell us how it holds up
We email owners 3 quick questions now and every 6 months, then show the results here.
Questions buyers ask
Is the HALOT-X1 made by Creality or PioCreat?
It launched in 2025 under PioCreat, a Creality spin off. In the US it is now sold as the Creality HALOT-X1 on Creality's store and at Micro Center. It is the same printer.
Do I need the Combo with the AFU?
No. The AFU adds automatic refill and resin preheating. GamesRadar+ suggests it for the best results, but TechRadar could not get it feeding properly and DIY Machines found it did not fully empty the vat.
Does it work in a cold garage?
It has no heated vat, so cold rooms can cause failures. GamesRadar+ traced its only problems to a cold printing area. The AFU can preheat resin to 30 to 35 C.
Guides and rankings with the Creality HALOT-X1
Compare the Creality HALOT-X1 with
8 head to head comparisons. Most searched first.
Alternatives in 3D printers
See all ranked →We check prices every morning and compare them with each model's 2026 low. One email when real deals land, plus our 5 minute Friday roundup. Unsubscribe anytime.