Bambu Lab H2S vs Sovol SV08 Max
Researched by Riley Hart · prices checked Nov 4, 2026
As of Nov 4, 2026, the Bambu Lab H2S costs $1,049 and the Sovol SV08 Max costs $1,099, so the Bambu Lab H2S is $50 cheaper. The Bambu Lab H2S has a published review score and ranks #28 in our 3D printers ranking; the Sovol SV08 Max is not scored yet. Pick the Bambu Lab H2S for large prints and engineering filaments. Pick the Sovol SV08 Max for very large single color prints. The Bambu Lab H2S wins 3 of 4 points we can measure.
Who wins, point by point
The Bambu Lab H2S wins 3 of 4 points we can measure. Built from today's prices, the specs and independent tests for these two robots.
| H2S | SV08 Max | Winner | |
|---|---|---|---|
| Price today | $1,049 | $1,099 | H2S |
| Build volume | 340 x 320 x 340 mm | 500 x 500 x 500 mm | SV08 Max |
| Top print speed | 1000 mm/s | 700 mm/s | H2S |
| Max nozzle temp | 350°C | 300°C | H2S |
- You want to spend less (saves $50)
- You care most about top print speed (1000 mm/s vs 700 mm/s)
- You care most about max nozzle temp (350°C vs 300°C)
- Best for large prints and engineering filaments
- You care most about build volume (500 x 500 x 500 mm vs 340 x 320 x 340 mm)
- Best for very large single color prints
- Build volume
- 340 x 320 x 340 mm
- Max speed
- Up to 1,000 mm/s
- Multicolor
- Yes
- Enclosure
- Yes
Big single nozzle enclosed printer for large and engineering prints
Full Bambu Lab H2S review, pros and cons →- Build volume
- 500 x 500 x 500 mm
- Max speed
- Up to 700 mm/s
- Multicolor
- No
- Enclosure
- Optional kit
Huge 500 mm cube Klipper printer for big parts and props
Full Sovol SV08 Max review, pros and cons →Side by side
| Bambu Lab H2S | Sovol SV08 Max | |
|---|---|---|
| Price | $1,049 | $1,099 |
| 3 year cost | $1,049 | $1,099 |
| Our score | 6.1/10 | Not scored yet |
| Rank in 3D printers | #28 | #48 |
| Status | on sale | on sale |
| Warranty | n/a | n/a |
| Build volume | 340 x 320 x 340 mm (Bambu Lab) | 500 x 500 x 500 mm; 500 x 500 x 450 mm with the enclosure kit (Sovol) |
| Print speed | Up to 1,000 mm/s toolhead speed, 20,000 mm/s2 acceleration (Bambu Lab) | Up to 700 mm/s, 40,000 mm/s2 (Sovol); Tom's Hardware printed at 40 to 140 mm/s and ran a Benchy in 10 min 45 s |
| Multi color | Yes with AMS 2 Pro (AMS Combo version); single nozzle, so color changes purge filament. CGMagazine says chained AMS units can hold 16 or more spools | No, single color; an auxiliary feeder handles filament feed (Tom's Hardware) |
| Enclosure | Yes, fully enclosed with active chamber heating up to 65 C (Bambu Lab) | Optional kit with metal panels, glass doors and rear fans; doors rattled at speed in Tom's Hardware testing |
| Auto leveling | Yes, automatic calibration; first run calibration took about 30 minutes for The Gadgeteer | Eddy current bed scan in seconds (Tom's Hardware); quad gantry leveling (Sovol) |
| Max nozzle temp | 350 C (Bambu Lab) | 300 C, 0.4 mm hardened steel nozzle |
| Heated bed | Yes, up to 120 C (CGMagazine, The Gadgeteer) | Up to 100 C, double sided PEI spring steel |
| Filament types | PLA, PETG, TPU, ABS, ASA, PC, PPA, PA6 GF, PAHT CF and other fiber filled engineering filaments (Bambu Lab) | n/a |
| Connectivity | Cloud, LAN, full offline mode, USB drive (not included); MQTT access in Developer Mode (Bambu Lab) | n/a |
| Camera | Yes, 3 cameras including a top down BirdsEye camera and a toolhead camera, with AI failure detection (Bambu Lab) | Yes, 1280 x 720 (Sovol) |
| Noise | Below 50 dB (Bambu Lab claim, measured at 1 m) | Loud; fans run whenever it is on (Tom's Hardware); no dB figure |
| Assembly | Ships assembled; CGMagazine says unboxing needs two people and setup with calibration can take more than 30 minutes | n/a |
| Weight | 30 kg printer alone, 40.7 kg AMS combo (The Gadgeteer) | 29.5 kg without enclosure; 700 x 710 x 750 mm footprint (Tom's Hardware) |
| Firmware | n/a | Klipper |
| Best for | large prints and engineering filaments | very large single color prints |
| Skip if | you print lots of multi color models | you want quiet, hands off printing |
Specs are maker claims unless a reviewer is named. Prices from the stores we link, checked daily.
What reviewers found
Bambu Lab H2S
- CGMagazine (8/10): Called it refined and reliable. Real world print times were about 20 to 30% shorter than typical fast CoreXY profiles and aggregated XY error measured under 0.5 mm. Multi color prints ran a few hours longer than on the H2D on day long jobs, with considerable purge waste. Source
- The Gadgeteer: Ran the H2S AMS 2 Pro combo for about a month, often around the clock. First calibration took about 30 minutes, PETG CF prints finished well and the AMS 2 Pro was nearly error free. Downsides were purge waste on multi color jobs and the pricey optional Vision Encoder. Source
Sovol SV08 Max
- Tom's Hardware: Benchy in 10 min 45 s; an ABS container took 5 h 6 min at 140 mm/s. A large dragon took 2 days 8 h after five failures and a 0.2 mm Z offset fix. Called it a niche machine that fills its niche well. Source
- 3D Tech Valley: Claims 200+ hours of printing. A 300 mm calibration cube measured within 0.2 mm and the full bed scan took about 80 s. Rated it Highly Recommended but noted 2 to 3 h of assembly and a Klipper learning curve. Source
Questions buyers ask
Which is better, the Bambu Lab H2S or the Sovol SV08 Max?
The Bambu Lab H2S has a published review score and ranks #28 in our 3D printers ranking; the Sovol SV08 Max is not scored yet. Pick the Bambu Lab H2S for large prints and engineering filaments. Pick the Sovol SV08 Max for very large single color prints.
Which is cheaper?
The Bambu Lab H2S at $1,049, versus $1,099 for the Sovol SV08 Max, checked Nov 4, 2026.
What is the difference between the H2S and the SV08 Max?
Build volume: 340 x 320 x 340 mm (Bambu Lab) on the H2S, 500 x 500 x 500 mm; 500 x 500 x 450 mm with the enclosure kit (Sovol) on the SV08 Max. Print speed: Up to 1,000 mm/s toolhead speed, 20,000 mm/s2 acceleration (Bambu Lab) on the H2S, Up to 700 mm/s, 40,000 mm/s2 (Sovol); Tom's Hardware printed at 40 to 140 mm/s and ran a… on the SV08 Max. Multi color: Yes with AMS 2 Pro (AMS Combo version); single nozzle, so color changes purge filament… on the H2S, No, single color; an auxiliary feeder handles filament feed (Tom's Hardware) on the SV08 Max.
Also consider at this price
See all ranked →More comparisons
All 3D printers, ranked
See the ranking →Affiliate links. We may earn a commission. It never changes our score. Disclosure
We check prices every morning and compare them with each model's 2026 low. One email when real deals land, plus our 5 minute Friday roundup. Unsubscribe anytime.